Quality Magazine logo

2022-04-19 07:26:09 By : Ms. Flower Wen

Ultrasonic technology has been used for testing ERW welded pipe at various points in the manufacturing process for many years. ERW pipes are manufactured by cold forming a strip of steel into a cylindrical shape using forming rolls, and then having a high frequency electrical current pass between the strip edges increasing the temperature of the steel to its melting point. The strip edges are forced together until the molten metal is forced out of the joint forming a weld bead. The bond is created without filler material. This longitudinal weld seam differentiates it from seamless pipe. During the welding process, the inner diameter and outer diameter weld flash is removed. At this point in the process, a variety of defects can occur, and ultrasonic inspection is well suited for identifying process problems in the weld zone.

Unlike single element traditional ultrasound, phased array technology uses a 3” wide array with 128 small transducers that are electronically pulsed together to make multiple sound beams covering an area of several inches. This allows the entire weld area to be covered without any mechanical movement. Utilizing phased array technology with a water gap between the array and the pipe allows the outer diameter to be monitored by measuring the change in the water path, while also monitoring the inner diameter by measuring the pipe thickness. The ability of phased array to electronically scan the length of the array results in several advantages: 

Echomac® PA TW screen for identifying defects in welded tube. Data is shown in concise manner using C-scan and summed A-scans for signals that cross the threshold for thickness variation and defect detection. A live B-scan view is also presented that allows the operator to easily align the system with the current weld position. Source: Magnetic Analysis Corporation

During the weld process, a variety of defects can be created in the weld seam. Lack of fusion, porosity, penetrator and hook cracks are a few of the typical defects. Ultrasound is used to inspect the weld for these types of defects. Longitudinal defects are detected by transmitting sound into the weld at an angle optimum for the defect type. Depending on the pipe wall thickness, multiple transducers can be required focused on the ID, OD and mid-wall. Multiple angles can also be used, but each angle needs a separate transducer, which requires complex mechanics and constant operator intervention. Phased array technology offers the ability to generate multiple sound beams focused at different areas of the weld and at different angles. Also, the ability to generate multiple sound beams allows the weld to be scanned and results in complete coverage.

Echomac® PA TW Test Head shown in gantry (robot alternative) positioning system for placing the head on the welded tube for testing. Source: Magnetic Analysis Corporation

Testing immediately after the welder offers the challenge of a very hot weld, a pipe that is not yet formed perfectly round and has vibration. This presents issues in getting accurate sound measurements. Ultrasound requires a liquid coupling medium and if water is used, the heat of the weld can create steam. Transmitting sound into the pipe is done by a test head with a captive water chamber that typically uses mill coolant. Sound cannot travel through bubbles because they interfere with sound transmission. To ensure that all bubbles are removed, the test head must be designed to vent the steam and provide a bubble-free coupling chamber for sound transfer. The issue of the out of round shape means that the water chamber cannot perfectly maintain a good seal with the pipe to contain the coupling fluid. Without a good seal, air pockets can develop in the chamber preventing sound from being transferred into the pipe. Design considerations must also be made to ensure adequate water flow. The vibration typical of a weld mill means that the test head must be designed in a manner that will keep the array transducer perpendicular to the pipe. This can be achieved using a series of springs and bushings. This same test system can be installed after the sizing rolls and before the cut-off saw. At that point the weld is cool, the pipe is round, but the location of the weld is not fixed. The system needs to have the ability to place the test head on the weld location and be adjusted as the weld varies. An economical approach is to use a robot and allow the operator to adjust the test head position. With phased array electronics becoming more economical, the overall cost of phased array versus single element is greatly reduced. The phased array electronics and transducers are more expensive but the savings on mechanics makes the overall cost very comparable. The use of phased arrays for the inspection of ERW pipe provides several benefits: 

In conclusion, the advancement of phased array technology creates a powerful way to identify defective welds in tubes by offering the operator easy to interpret images for quickly determining the types of defects present in the welding process. This capability reduces scrap and ensures product quality for end customer use in critical applications.  

Michael Moist is global sales manager PA-UT for Magnetic Analysis Corporation.

You must have JavaScript enabled to enjoy a limited number of articles over the next 30 days.

Sponsored Content is a special paid section where industry companies provide high quality, objective, non-commercial content around topics of interest to the Quality audience. All Sponsored Content is supplied by the advertising company. Interested in participating in our Sponsored Content section? Contact your local rep.

Submit a Request for Proposal (RFP) to suppliers of your choice with details on what you need with a click of a button

Browse our Online Directories and save time finding what you’re looking for anytime, anywhere!

The pandemic has had a lasting effect on the remote preferences of the workforce. Join ETQ experts to learn how ETQ’s mobile solution can extend your quality processes to workers on the manufacturing floor, agents in the field, auditors on the go, and anyone else who needs quality management at their fingertips.

Celebrating our 10th anniversary, The ASSEMBLY Show brings together thousands of attendees and hundreds of exhibitors showcasing the latest assembly technology, equipment, and products. Mark your calendar and plan to be a part of this milestone event where participants will uncover new resources, evaluate the latest technologies and products, learn from industry experts, and connect with experienced professionals.

Copyright ©2022. All Rights Reserved BNP Media.

Design, CMS, Hosting & Web Development :: ePublishing